Manchester, NH

Replace mixing valve on water heater and replace the toilet tank flapper that constantly runs.

Drain down tube exhanger for glycol loop #2. Flush water through system. Refill loop with glycol. Purge air. Let system run. Test dilution with refractometer. System is protected down to -4 deg F freeze and approximately -40 deg F burst. We recharged air into expansion tank to match the system operating pressure. Make adjustments to help with humidity issues.

Air in oil line. Reset it. Cycled system multiple times. Took combustion test. Youre all set. Thank you very much.

Everything went great on your GSMS plumbing visit. We maintained the tankless water heater and did a plumbing inspection. We will send an estimate for our reccomended repairs.

Disconnect unit heater gas piping. Cap in place. Test for leaks. Disconnect venting. Cap venting. Gas is off at the meter.

I started off with turning on the Haier mini split heads upstairs. After a few minutes of them running, they both came up with a F1 error code. I then went outside to take a look at the unit. I found there to be a lot of ice built up on top and around the unit. I called into tech-support to find out what was going on with the unit. After doing some testing, we found it to be a bad PCB board outside. Tech-support recommended replacing the inverter board and PCB board together.

Replace leaking 3/4inch 90. Test piping for leaks with bubbles. Relight appliances.

We found the pilot to be out. The thermocouple was dirty. We cleaned the thermocouple and relit the system.

Found that thermostat replaced with customer thermostat

Installation of a 6 gallon electric water heater to provide the office bathroom with hot water. We also installed a Taco LeakBreaker to protect and prevent water damage in the future.

Replacement of existing gas furnace only. Exiting A/C will remain in place.

Service switch was off. I turned it back on and completed a combustion test. Heat is back on.

Add a supply duct and register into Robbie's room. A central return with a filter grill will be added to the ceiling in the hallway because whoever remodeled the apartment removed the return duct from the hallway. The return is in the attic space which is dangerous with the venting being in the same space. 14x24x1 filter size.

Checked gas pressure,checked burners and cleaned flame sensor

Replace buried oil line with new coated oil line. Install tigerloop to oil delivery system. Check for leaks and start system. We noticed that the furnace is short cycling due to an undersized return duct design. We surpassed the NTE so we did not perform the other requested tests.

Installation of a single-zone mini-split system to serve the basement area; based on the understanding that the basement will be finished off. Indoor unit placed in nook of basement by workout equipment, centered on wall. We will add 1/2" plywood backing to "stand" the unit off of the wall for future drywalling to but up on the sides. Drain will gravity feed outside to the exterior with 3/4" PVC. Line set will follow along HVAC trunk to reach exterior unit location. Outside unit will be placed next to existing central system unit. Ground will be leveled off with cement block to make a retaining wall for the unit to sit on. Electrical circuit added to support new system. Existing exterior outlet is already in place to meet code. Also adding an option to install a whole home air purifier for your central system to provide clean and healthy air. This is at a discounted rate as we will already be present installing the mini-split system.

Assist in testing glycol.

Replaced kitchen cartridge and shower hose

Thaw out pipe,new new switch on condensate pump check for warranty

Replaced flue pipe,chimney needs inspection

Check gas pressures and vent.Notice in coming pressure was lower than last time.Contacting Rinnai rep to go over some things.

Diagnosed a loose wire. Found the circulator to be receiving power but not running. We replaced the pump, relief valve, and expansion valve. We found the flue pipe needs to be replaced. We will come back tomorrow to replace.

I started off with inspecting the kitchen sink. I looked for any signs of corrosion or leaks and everything looked very good. Next, I went to the three bathrooms. The bathroom on the first floor everything looked and operated good. The bathroom upstairs with the tub, the toilet would run for a couple minutes after flushing. The other bathroom with the stand up shower the sink drain looked like it had some buildup on the threaded connection. I took pictures of the toilet and the sink drain for our plumbing team to take a look at. Everything else in the two bathrooms looked and operated good. Next, I went downstairs and inspected all of the pipes in the boiler room for corrosion or leaks. I didn’t find any leaks, but I did find the relief valve on the water storage tank to be dripping. I took a look at the water meter and everything looked good there. I did find under the oil tank to be a little wet. I attached photos of the toilet, drain and oil tank. Lastly I checked the washer machine

After doing a few test, I found that the thermostat upstairs that we installed last year was faulty. I was going to replace it with the same generation three thermostat, but they didn’t have any in the color that he had. I upgraded to the generation four nest thermostat.

Had to order different cartridge,also wants to order new shower hose for shower 60” long chrome